+- Hack Forums (https://hackforums.net)
+-- Forum: Hacks, Exploits, and Various Discussions (https://hackforums.net/forumdisplay.php?fid=45)
+--- Forum: Grayhat • Purple Team • Hybrid Security (https://hackforums.net/forumdisplay.php?fid=449)
+---- Forum: Beginner Hacking (https://hackforums.net/forumdisplay.php?fid=4)
+---- Thread: Darkcomet not showing slaves (/showthread.php?tid=2997750)
Darkcomet not showing slaves - Leon_V._Metcalf - Nov 4, 2012
Hello members of HF. I have been experiencing some problems with Darkcomet. I have correctly portforwarded (when I went to canyouseeme.org, it says that port * was a success) and disabled all my AVs. I also followed Plutonium's tutorial on how to setup Darkcomet (https://hackforums.net/showthread.php?tid=2698687), and followed everything mentioned in the thread. I didn't even encrypt the server, I ran it raw on Sandboxie. It doesn't even show me! I also read the "Help" section of the Darkcomet program, and it said something about not using NAT in VMware. Problem is, I have a NAT router. Is this causing the problem? ❓
Sorry, this is my first time using a RAT, so correct me if I have any mistakes.
* - Vandal - Nov 4, 2012
Have you setup a no-ip? That could be your problem. Are you also listening to the port in darkcomet?
* - Leon_V._Metcalf - Nov 4, 2012
(Nov 4, 2012 05:25 PM)Vandal Wrote: Have you setup a no-ip? That could be your problem. Are you also listening to the port in darkcomet?
Oh yes, I forgot to mention that too. I already made an account and used my host name as the address for darkcomet. And I am also listening to a port with uPNP Automatic Portfowarding enabled.
* - J0sh - Nov 4, 2012
https://hackforums.net/showthread.php?tid=2816482
Glad i could help.
* - Leon_V._Metcalf - Nov 4, 2012
(Nov 4, 2012 08:53 PM)J0sh Wrote: https://hackforums.net/showthread.php?tid=2816482
Glad i could help.
Did this, still no luck. I did successfully portfoward port 200; canyouseeme.org confirms it, yet, I do not see anyone in the users pane even after I ran the server in Sandboxie....
😟
* - Leon_V._Metcalf - Nov 7, 2012
Nevermind. Tested my server using 127.0.0.1 and confirmed it works. Sorry for the hassle, I'm still new to this. Thank you for all your efforts.
* - Diаmond - Nov 7, 2012
You might have not port forwarded right, go to canyouseeme.org to check if your port is open.
* - Leon_V._Metcalf - Nov 7, 2012
(Nov 7, 2012 06:44 PM)Dɪᴀᴍᴏɴᴅ Wrote: You might have not port forwarded right, go to canyouseeme.org to check if your port is open.
Says "Success!" port is open. I have a question, when I run the server in Sandboxie configured to my no-ip address, is it supposed to show on Darkcomet, or am I supposed to run it on another computer in a different network? The only way I found to make myself show up was to run the server configured to 127.0.0.1 on Sandboxie. Thanks again.
* - Yaanst - Nov 9, 2012
(Nov 7, 2012 07:30 PM)Leon_V._Metcalf Wrote: I have a question, when I run the server in Sandboxie configured to my no-ip address, is it supposed to show on Darkcomet, or am I supposed to run it on another computer in a different network? The only way I found to make myself show up was to run the server configured to 127.0.0.1 on Sandboxie. Thanks again.It depends, sometimes it shows up sometimes it doesnt. I know that on my network it shows up.
* - PoisonKnife - Nov 9, 2012
Did you use a password when you made the server?
If yes, have you typed it into the the client?
* - Brum The Original - Nov 9, 2012
this might be because you used no ip wich is for other people use 127.0.0.1 if you're using it on yourself and then it will show up
* - Leon_V._Metcalf - Nov 9, 2012
(Nov 9, 2012 07:23 AM)PoisonKnife Wrote: Did you use a password when you made the server?
If yes, have you typed it into the the client?
No, I did not put a password. I am aware of the glitch...
(Nov 9, 2012 07:24 AM)The Ice King Wrote: this might be because you used no ip wich is for other people use 127.0.0.1 if you're using it on yourself and then it will show up
Thanks! I think I'm starting to understand how this RAT works. If I used my no-ip address and someone runs it, they will show up right? And do I have to be online with Darkcomet open when they run the server in order for the slave to show up?
* - Mac1339gold - Aug 6, 2013
im sorry to say but the port that you opened is the wrong one. the real one is port 1604 so try that.
* - T0ucaNSaM - Aug 6, 2013
Try Disabling NAT on the router idk if that is an option.What kind of router is it ?
* - futuro9711 - Jul 5, 2014
same prob i have i tried all things i also use 127 type but it also not responsing i m not getting where is the problem