OMC [TUTORIAL] INSTALL AND USE OMNICOIN-QT

Code
# omnicoin.conf configuration file. Lines beginning with # are comments.



 # Network-related settings:



 # Run on the test network instead of the real omnicoin network.

 #testnet=0



 # Connect via a socks4 proxy

 #proxy=127.0.0.1:9050



 ######

 ##      Quick Primer on addnode vs connect      ##

 ##  Let's say for instance you use addnode=4.2.2.4      ##

 ##  addnode will connect you to and tell you about the      ##

 ##    nodes connected to 4.2.2.4.  In addition it will tell ##

 ##    the other nodes connected to it that you exist so     ##

 ##    they can connect to you.      ##

 ##  connect will not do the above when you 'connect' to it. ##

 ##    It will *only* connect you to 4.2.2.4 and no one else.##

 ##      ##

 ##  So if you're behind a firewall, or have other problems  ##

 ##  finding nodes, add some using 'addnode'.      ##

 ##      ##

 ##  If you want to stay private, use 'connect' to only      ##

 ##  connect to "trusted" nodes.      ##

 ##      ##

 ##  If you run multiple nodes on a LAN, there's no need for ##

 ##  all of them to open lots of connections.  Instead      ##

 ##  'connect' them all to one node that is port forwarded   ##

 ##  and has lots of connections.      ##

 ##      Thanks goes to [Noodle] on Freenode.      ##

 ######



 # Use as many addnode= settings as you like to connect to specific peers

 #addnode=204.44.122.123

 #addnode=192.99.42.164

 #addnode=192.99.42.206

 #addnode=192.99.42.238



 # ... or use as many connect= settings as you like to connect ONLY

 # to specific peers:

 #connect=69.164.218.197

 #connect=10.0.0.1:8333



 # Maximum number of inbound+outbound connections.

 #maxconnections=



 # JSON-RPC options (for controlling a running Omnicoin/omnicoind process)



 # server=1 tells Omnicoin-QT to accept JSON-RPC commands.

 #server=0



 # You must set rpcuser and rpcpassword to secure the JSON-RPC api

 #rpcuser=HackForums

 #rpcpassword=YourSuperGreatPasswordNumber_DO_NOT_USE_THIS_OR_YOU_WILL_GET_ROBBED_385593



 # How many seconds omnicoin will wait for a complete RPC HTTP request.

 # after the HTTP connection is established. 

 #rpctimeout=30



 # By default, only RPC connections from localhost are allowed.  Specify

 # as many rpcallowip= settings as you like to allow connections from

 # other hosts (and you may use * as a wildcard character).

 # NOTE: opening up the RPC port to hosts outside your local

 # trusted network is NOT RECOMMENDED, because the rpcpassword

 # is transmitted over the network unencrypted.

 #rpcallowip=10.1.1.34

 #rpcallowip=192.168.1.*



 # Listen for RPC connections on this TCP port:

 #rpcport=8332



 # You can use Omnicoin or omnicoind to send commands to Omnicoin/omnicoind

 # running on another host using this option:

 #rpcconnect=127.0.0.1



 # Use Secure Sockets Layer (also known as TLS or HTTPS) to communicate

 # with Omnicoin -server or omnicoind

 #rpcssl=1



 # OpenSSL settings used when rpcssl=1

 #rpcsslciphers=TLSv1+HIGH:!SSLv2:!aNULL:!eNULL:!AH:!3DES:@STRENGTH

 #rpcsslcertificatechainfile=server.cert

 #rpcsslprivatekeyfile=server.pem



 # Miscellaneous options



 # Set gen=1 to attempt to generate omnicoins

 #gen=0



 # Pre-generate this many public/private key pairs, so wallet backups will be valid for

 # both prior transactions and several dozen future transactions.

 #keypool=100



 # Pay an optional transaction fee every time you send omnicoins.  Transactions with fees

 # are more likely than free transactions to be included in generated blocks, so may

 # be validated sooner.

 #paytxfee=0.00



 # Allow direct connections for the 'pay via IP address' feature.

 #allowreceivebyip=1



 # User interface options



 # Start Omnicoin minimized

 #min=1



 # Minimize to the system tray

 #minimizetotray=1